Use of ij.start canon to Setup Canon IJ Printer Properly
ij start Canon TS3122 How to Connect Wireless?
There are certain access points, which are also called as hubs or router, which have an automatic connection button that has a label WPS also called Wi-Fi protected setup. This is one way that enables the user to connect ij.start.canon ts3122 printer to your network. The best thing about such kind of wireless connections is that you are not required to enter any password and use a simple and quick method to connect your device. So far, this method is the easiest means to connect your ij.start.Canon TS3122 printer device. In case your device has a Wi-Fi protected setup button, then you need to choose the WPS connection method. Stated out below are the directions that you are required to follow. Also, if your router device does not support Wi-Fi protected setup, then you can take a look at alternate instructions given under the Standard connection method to connect your Canon PIXMA printer. So, here are certain steps that you need to follow in order to perform ij.start.canon ts3122 setup. Wi-Fi Protected Setup Connection Method: 1- Before getting started, there are certain conditions that you are required to meet to be able to use the WPS push button method. 2- The most important thing that you need to ensure is that your router needs to have a physical WPS push button on it. Before going forward with the process, you need to check the user guide of your device in order to obtain the information to run it properly. 3- In case the WPS push button is not available, then you can carry out the instructions that are given under standard connection method. You must ensure that your network is WPA2 or WPA security protocols. These protocols are generally used by the most WPS-enabled routers. So, Here are the Steps that You need to Carry Out for IJ.Start.Canon.TS3122 Setup- Step 1: A.) - Please ensure that your printer device is powered on. B.) - Press the button of Wi-Fi and then hold it down. Keep on holding it till you see the alarm light blinking before you. Step 2: A.) - Please ensure that the light which is placed right after that button begins to blink blue and then go to your router device and then push the WPS button within 120 seconds. B.) - In order to get perfect information on how to start WPS on your access point, take a look at the user guide. C.) - The blue Wi-Fi lamp on your printer machine will continue to flash while you are searching. The Wi-Fi lamp and the power button will start flashing at the time of connecting to the access point. D.) - Once a stable connection is established between your printer and wireless network, then the Wi-Fi light and the power light will start flashing and will remain turned on. Confirm the Settings of the Network- In order to confirm that your printer device is connected to the wireless network, you can try out printing the network settings of the printer if you wish to. 1.) - In order to confirm that your printer device is connected to the wireless network, you can try out printing the network settings of the printer if you wish to. 2.) - Press the button of Cancel or Resume and keep on holding it until the light of your alarm flashes 15 times and then leave it. 3.) - Print out of network information page will come out. At the time of referring to the printout, see if your connection says active and also check that the name of your wireless network is showing up the correct name of the wireless network. How to Setup Canon Pixma MX490 Printer? Here, we shall cover the basic steps to cover the wireless setup of Canon Pixma MX490 Printer to your system. Steps for Cable Setup of Canon MX490 Printer: Let us discuss the Canon Pixma MX490 setup using standard wireless set up as discussed below: Step 1 : Before connect Canon mx492 printer to wifi, assure that your router is properly set up and no network issue prevails. Make sure system and network are connected smoothly for further procedure. Step 2 : Make sure printer is plugged into socket and powered “ON”, green LED light indicates that printer is ON. Step 3 : If the screen display is blank after printer is turned ON, press the copy button, followed by the Setup button after screen is ON at touch panel display. Setup button is at bottom right of the four button panel displayed below. Step 4 : The screen will display wireless LAN setup options on touch panel, press OK button and it will search for various modes. Press stop until below display (Wireless LAN setup>Standard setup) appears on the screen. Step 5 : Scroll right for various options and press ok after selecting cable less setup on your Canon Pixma MX490 printer touch display panel. Step 6 : Now install Canon MX490 Printer software either through the CD rom that comes with your printer or you could also manually download through the canon web site. Step 7 : Start with your language, country and select the model of the printer i.e. Canon Pixma MX490 or MX492 as shown below. Step 8 : Select the device, operating system (Windows) and select the folder to download the driver file. Run the downloaded file and run the set up by clicking next. Step 9 : Select wireless LAN connection printer method as Canon Pixma MX490 printer connection method and select connect via wireless router method. Step 10 : Make sure Canon Pixma MX490 Printer is ON, the software will search for printers already connected to the network, if it is the first time list shall be blank and check inbox setting printer could not be found on list, else click next. Step 11 : Setup guide shall be installed on your system and click next in cable-less setup submenu. The network connection will disable for a short time and reconnect shortly. Step 12 : After network has been restored, installation shall start and click on license and agreement to start the process, click on complete tab after the option displayed after setup being installed. Step 13 : After canon mx490 printer installation, next step is Set up means page alignment and then last point having registration and surveys, if you want to skip the survey and registration you can continue for test page print and click the execute button. Step 14 : Now you could see installation completed successful display and now you are ready to print or scan using Canon Pixma MX490 printer. Hope the above steps are helpful in connecting your Canon printer MX490 and carry on smooth operations. Or Visit to Download Canon Printer Driver Source - https://www.easyprintersupport.com/canon-com-ijsetup/ Tag - #ijstartcanon, #ij.start.canon, #Canon.com/ijsetup, #https://ij.start.canon